Customers find the reacher clips to be a nice little product with good ideas, though they are too small for many walkers and grabbers. Moreover, the clips are flimsy and don’t stay on the walker, with customers reporting they pop off easily. Additionally, the functionality is limited to specific circumstances, and customers consider it an absolute waste of money.
AI Generated from the text of customer reviews
8 reviews for Sammons Preston Clip for Feather Reach Reachers, Pack of 10 Holder Clips for Grabber Tool Storage on Walkers, Rollators, Canes, & Wheelchairs, Attachment for Accessibility Tool
0.0out of 5
★★★★★
0
★★★★★
0
★★★★★
0
★★★★★
0
★★★★★
0
Write a review
Show allMost HelpfulHighest RatingLowest Rating
Redeemed –
they stay put for me…
I rarely leave my apt without it & pickup tool attached to my walker….I find no fault with them, have only used one so far with others as spares, worth every penny.Hope they’re not made in China! 🙂
Helpful(0)Unhelpful(0)You have already voted this
Bob Kerns –
They are too small for any walker, cane, or wheelchair that I own. They energetically pop off
They are too small for any walker, cane, or wheelchair that I own. They barely clip on, but then energetically pop off at the slightest provocation. The reacher side is fine for my my RMS reachers (which I highly recommend). I am going to experiment with glueing them in place rather than return them.
Helpful(0)Unhelpful(0)You have already voted this
hitchicken –
Narrow functionality. Marginal performance.
I love my RMS Featherweight Reacher. I’d love to have it everywhere, but carrying it around is a pain. These clips work well holding my grabber to my cane. Even so, they are somewhat fragile and break a bit easier than I’d like. My RMS grabber has a rectangular cross-section that these clips fit. If you don’t… these clips probably won’t work for you.These clips do not work for most other circumstances including round shafted or non-rectangular reachers of different dimensions. These clips will break on wider tubes making up some canes, most walkers and most wheel chairs. Even 1″ diameters quickly fatigue and break these clips.More accurate dimensions of these clips might help you make up your own mind as to whether they will work for you. I’ve included a photo of a diagram of a clip with dimensions as best as I could measure. I also included a photo of a clip holding my reacher to my cane.These clips address a very narrow and specific requirement and are unlikely to fulfill most needs.
Helpful(0)Unhelpful(0)You have already voted this
Veronica –
Too small
I wish they had shown a picture of a reacher/grabber actually in the clip holder. The clip is actually smaller and not as sturdy as I was expecting.Also my mom’s grabber would not fit in the holder without using a LOT of strength > of which she does not have. I don’t think it would have remained in the clip anyway as it was a little small.
Helpful(0)Unhelpful(0)You have already voted this
RetiredMSW –
It fits perfectly but isn’t nearly as strong as the original
I love this item because it fits a rack that I have perfectly. I always know where my reacher tool is. However these replacement pieces are way less sturdy than the original piece that came on the reacher tool. Because the plastic is much thinner, I think it is a bit overpriced and probably won’t last long. Maybe that’s why there are several in the package. I hope I am wrong about it being easily broken.
Helpful(0)Unhelpful(0)You have already voted this
PAUL CARPER –
Five Stars
Nice little product I use to hold my grabber onto the walker.
Helpful(0)Unhelpful(0)You have already voted this
LaJuana –
Horribly disappointing
It will not stay put. Slides all over the leg.Pops off when I try to get the reacher. Great idea but wrong material. And I need it so badly to work. 3 major back surgeries in 6 months. Can’t bend. Any suggestions for one that DOES work??!!
Helpful(0)Unhelpful(0)You have already voted this
Brad Tyrrell –
Small
Works OK, but a bit too small for my walker and grabber.
Redeemed –
they stay put for me…
I rarely leave my apt without it & pickup tool attached to my walker….I find no fault with them, have only used one so far with others as spares, worth every penny.Hope they’re not made in China! 🙂
Bob Kerns –
They are too small for any walker, cane, or wheelchair that I own. They energetically pop off
They are too small for any walker, cane, or wheelchair that I own. They barely clip on, but then energetically pop off at the slightest provocation. The reacher side is fine for my my RMS reachers (which I highly recommend). I am going to experiment with glueing them in place rather than return them.
hitchicken –
Narrow functionality. Marginal performance.
I love my RMS Featherweight Reacher. I’d love to have it everywhere, but carrying it around is a pain. These clips work well holding my grabber to my cane. Even so, they are somewhat fragile and break a bit easier than I’d like. My RMS grabber has a rectangular cross-section that these clips fit. If you don’t… these clips probably won’t work for you.These clips do not work for most other circumstances including round shafted or non-rectangular reachers of different dimensions. These clips will break on wider tubes making up some canes, most walkers and most wheel chairs. Even 1″ diameters quickly fatigue and break these clips.More accurate dimensions of these clips might help you make up your own mind as to whether they will work for you. I’ve included a photo of a diagram of a clip with dimensions as best as I could measure. I also included a photo of a clip holding my reacher to my cane.These clips address a very narrow and specific requirement and are unlikely to fulfill most needs.
Veronica –
Too small
I wish they had shown a picture of a reacher/grabber actually in the clip holder. The clip is actually smaller and not as sturdy as I was expecting.Also my mom’s grabber would not fit in the holder without using a LOT of strength > of which she does not have. I don’t think it would have remained in the clip anyway as it was a little small.
RetiredMSW –
It fits perfectly but isn’t nearly as strong as the original
I love this item because it fits a rack that I have perfectly. I always know where my reacher tool is. However these replacement pieces are way less sturdy than the original piece that came on the reacher tool. Because the plastic is much thinner, I think it is a bit overpriced and probably won’t last long. Maybe that’s why there are several in the package. I hope I am wrong about it being easily broken.
PAUL CARPER –
Five Stars
Nice little product I use to hold my grabber onto the walker.
LaJuana –
Horribly disappointing
It will not stay put. Slides all over the leg.Pops off when I try to get the reacher. Great idea but wrong material. And I need it so badly to work. 3 major back surgeries in 6 months. Can’t bend. Any suggestions for one that DOES work??!!
Brad Tyrrell –
Small
Works OK, but a bit too small for my walker and grabber.